If you’re eager to be finished hauling heavy pots of water from the kitchen sink to the cooktop the pot filler may be the perfect solution. Of course, you’ll have to learn how to install a pot filler faucet.
These practical devices take away the long, careful walking between the sink and the cooking surface. Although you’ll still need to take the water out in the sink, it will eliminate the majority of the journey.
Mounting a pot filler isn’t complicated, but certain factors could complicate the procedure. If you’re planning to renovate the kitchen, begin to build a new home, or work on a current wall the installation of a pot filler is feasible.
Check out this tutorial on how to install a pot filler. You can then decide if it’s something you’re able to handle, or if you’re required to get a plumber who is professional.
- 1 Where Should a Pot Filler Be Placed?
- 2 Is It Hard to Mount a Pot Filler in a Current Wall?
- 3 4 Steps How to Install a Pot Filler Faucet
- 4 The Factors to be Considered When Installing the Heavy Pot Filler
- 5 Is it Difficult to Install a Pot Filler?
- 6 Video: How to Install a Pot Filler
- 7 FAQs
- 8 Conclusion
Where Should a Pot Filler Be Placed?
A faucet to fill a pot comes over the stove, which means the arm of the faucet can extend and lie directly over the top of a pot. This allows you to place your pot on a burner and then fill it with water without having to move it.
Review the directions included with the pot filler faucet that you bought and then review your local building codes to determine if there are any information guidelines on where to put it.
The dimensions of the faucet’s height can be different based on your preferred style. As per Kingston Brass, the general advice is to mount the faucet that fills pots from 16-36 inches (40 centimeters to 1 meter) above the top surface of your range. If you install it at a low level, you will not have the space to place large pots beneath it.
To determine how high you need to mount it, location your highest pot on the stove, take a measurement of it, then add some inches. Be aware that if put the pot filler is too high, it could cause splashing, be uncomfortable and make it impossible to access.
A spot that is centered over the band is a popular spot for the installation of pot fillers. Take note of how far the faucets for pot fillers extend to figure out how far they can reach every burner.
If you have one main burner to fill your large pots, it is possible to pick an offset spot close to that burner. In the event that your kitchen is close to a wall on the side, it is possible to set the pot filler to the sidewall.
Is It Hard to Mount a Pot Filler in a Current Wall?
In certain situations, installing a pot filler in a current wall can be difficult. The procedure is much simpler in the event of a complete kitchen renovation or starting with a brand new construction. For example, when the wall behind the cooker consists of a solid surface that needs particular tools to drill through, the procedure could be difficult.
Also in the case when it’s necessary to bring a water line to the inside of the wall that is behind the stove. This can be difficult, particularly when you’re unfamiliar with DIY projects such as those. Often, there’s not a water supply line in the near location of the place you need the new water line.
This means that you'll need to connect to the closest existing line. This could be the one that connects to the refrigerator icemaker, kitchen faucet, or dishwasher. New water lines have to be connected to the pipe and then bring to the new pot filler location.
If you’re not sure that installing a pot filler is something you’re comfortable with, it is recommended to hire an expert to put in the new fixture. Making a mistake in this portion of the process could result in a myriad of unwanted issues including damaging leaks or low-pressure water, or any other issues within the plumbing system.
4 Steps How to Install a Pot Filler Faucet
Before installing an appliance to fill a pot it is necessary to bring a water supply line to the location. To rough in the pot filler, you have to determine exactly where you would like it to stand. Specific plumbing guidelines will differ between the models that follow, so make sure to check the manual of the user before beginning.
Step 1. Shut off the Water Supply Line
For any plumbing job, it is essential to turn off all water lines to the location. Therefore, prior to working on plumbing lines that supply water to the area, be sure that you shut off the proper valves shutting off the water.
After you’ve finished that, you should turn on all kitchen faucets in order to release the pressure of water in the lines.
Step 2. Make the Rough-in Plumbing
You’ll require a stub-out pipe from your water source. The majority of pot fillers need a threaded elbow in order to direct the water from the wall and towards the filler. Probably, you will need to fit a nipple of 1/2-inch.
Check the pot filler instructions to define the stub-out length which is usually around 1/2 inch (1 centimeter) from the wall or the installing surface. After you have completed the rough-in plumbing process, you can finish the mounting.
Step 3. Attach a Pot Filler to the Wall
Pot fillers are equipped with mounting plates which are fixed on the wall. The mounting plate usually goes over the plumbing and then is secured to the wall with screws.
There are pot fillers that have two mounting points where that attach to the mounting plates. Your pot filler has to include a clamp or gasket to attach it to the line for water supply.
Mount these pieces as described in the direction. Then, attach your pot filler faucet to the pipe. Secure any screws that connect your faucet to the mounting plate to those as per the directions.
Step 4. Test the Installation
After everything is mounted, check the installation to ensure that it isn’t leaking. Re-turn the water supply on. Set a bucket under the pot filler and then turn on the faucet for filling pots so that water flows into it, without leakage.
Allow it to run for a few minutes to flush any remains or impurities that may be in the line. Then shut it off to empty the bucket when needed.
The Factors to be Considered When Installing the Heavy Pot Filler
It’s possible that certain elements of the above information weren’t clear to you. When you’re setting up the pot filler and the water line you must ensure that you adhere to these steps.
- At any time you begin to work with water lines, you must turn off them prior to working.
- Utilize the one-valve pot fillers if you intend to mount them on your own.
- If you’re making use of the supply lines for water to cook, make sure the water has been filtered.
- If you opt to tighten your threads, don’t apply too much pressure while tightening them.
- Make sure to switch off the electrical line in the event that you intend to conduct anything plumbing-related.
- The installation of the pot filler might seem like a daunting undertaking but it’s going to save you money after the installation is completed.
- If you’re planning to utilize a big pot or pan, be sure to set it high.
- A pot filler does not only increase the worth of your house but will also provide the most convenience in your work. This is a good reason why you should seriously consider adding it to your house.
Is it Difficult to Install a Pot Filler?
When you’re substituting a current pot filler faucet during the course of a kitchen renovation it is possible to complete the task yourself. Removing the faucet you have is fairly simple. You just unscrew and remove the old pot filler, then mount the new installing plate and connect the new faucet to the current supply line. Here is the best wall mount bathroom faucet.
If you’re mounting an entirely new pot filler in a place that doesn’t have one, it could be highly complicated. Probably, there isn’t already a water line running precisely where you’ll require it. Even may not be an existing water line running through that wall or somewhere near the place.
This means that the plumbing for the pot filler has to connect to the nearest existing line. A new water line needs to connect to that pipe and then bring to the spot where the pot filler will be.
If you’re not experienced in plumbing, this portion of the job should be left to the professional plumber. Incorrect mounting can lead to damaging leaks, low pressure, or other problems to your plumbing system.
Video: How to Install a Pot Filler
In this video, you can watch step-by-step how to install a Pot Filler in the kitchen.
How do you install a kitchen pot filler?
Step 1. Shut off the water supply line.
Step 2. Make the rough-in plumbing.
Step 3. Attach a pot filler to the wall.
Step 4. Test the installation.
Is it worth it to install a pot filler?
If you’re trying to conserve room in the kitchen or trying to add some additional elegance, it’s clear that a pot filler can improve the functionality of your kitchen and appeal.
When you consider using a pot filler in lieu of the sink faucet, you will find numerous advantages. When the typical sink faucet provides an average flow of 1.5 gallons per minute, the pot fillers provide a flow of 4.0 gallons per minute.
This means that pots are filled up to 3 times quicker than with the other faucet in your kitchen.
Is it expensive a pot filler installation?
The price for mounting a pot filler depends on several elements. For example, the specifications of the product, as well as the process of installation and the specialist you select, can affect the price. According to how complicated this installation will be, it could be quite costly. Usually, it’s around $300 (on the lower price).
What is the best place for pot filler?
Generally speaking, a pot-filler is best placed situated on the left or right side of the cooktop. This will prevent having to reach over the cooking surface to access the tap, which could be hard if you have something cooking.
How much should the height of the pot filler be over the stovetop?
Fillers typically sit between 16 and 36 inches higher than the cooking surface. It depends on personal preferences. It is important to ensure you set the faucet up sufficiently high to accommodate the biggest pots beneath it. Larger dishes might not fit underneath pot fillers that are the wrong height, so choose the one that is most comfortable for your needs.
Does pot filler require two water lines?
The majority of pot fillers don’t require both water lines. Pot fillers don’t come with a mixer, and therefore they only distribute whatever they’re connected to. Thus, you can connect either a hot or a cold water line to the pot filler. Pot fillers are typically connected to the cold water lines however, a hot water line is also possible.
The intention behind this post was to provide the steps on how to install a pot filler faucet. Here is was covered the major aspects of the installation of a pot filler into your kitchen. In the realm of kitchen design pot fillers are a very popular and preferred option due to a variety of reasons.